Building a 24x18x6 frag tank

Hunna

Well-Known Member
Supporting
Contest Committee
Messages
458
Reaction score
721
Location
Marietta
Hey there! I’ve decided to build a frag tank myself instead of wait around and hope I can find a good price on one. I feel fairly confident in building out the tank aspect. I ordered 1/2” sheets of 24x18 (black), 2 clear sheets of 18x6, and 2 clear sheets of 24x6 off estreetplastics. I’m needing to cut down the 18x6 to 17x6. I asked them if they could do it for me, but if they can’t what’s my best option to cut the extra inch off each piece?

Past that, does anyone have any experience building an AIO compartment? I also feel like I’ll be able to figure this part out, but it wouldn’t hurt to have someone to run my ideas over with. I’m mainly wondering how easy/difficult it will be to cut out the hole for the return, and what tool would be needed for that? Any help would be greatly appreciated!
 
Best bet for cutting the sheets down to size would be a table saw.
Cutting the return holes is easy with a drill and hole saw.
I've got both at my shop off Mansell Rd if you'd like to stop by with your acrylic
 
Best bet for cutting the sheets down to size would be a table saw.
Cutting the return holes is easy with a drill and hole saw.
I've got both at my shop off Mansell Rd if you'd like to stop by with your acrylic
I manage the Play it Again Sports on Mansell Rd, so that works out perfectly! The main pieces shipped out today and they did not cut the 18x6 pieces, so this is a huge help!
 
EEEBD409-81A0-481E-9334-2B8633E0B486.jpeg

She’s just about there! Filled halfway with old tank water, mixing the rest currently. Added some rock and sponge from my other tanks and will be adding more once it’s full, to help skip the cycle process. ATO hooked up, return figured out, AIO compartment glued in with baffle cut out. AI 16 set on the exact same schedule as the one on my Waterbox that’s next to it, just lower %s for everything since there’s less water to go through. Hoping to have it fully up and running by the end of tomorrow!
 
I have masses of PVC board and it's main issue is it easily dents.

I do have plenty of experience building all sorts of things with acrylic, though I'm very far behind on commissions. I can still answer any questions though
 
I'm curious what kind of savings you've seen over buying one pre-made? I've been wanting to do this same thing, but decent acrylic is so expensive that I'm not sure it would save enough to be worth it. Though the custom dimensions may be worth it in and of itself.
 
08EDC3EC-5E37-4134-89CB-ECD6BC1D2488.jpeg
3218CDF6-1D78-412F-A8B9-FF913803C251.png
That was for the acrylic. Admittedly, I could have had a frag tray 3D printed from a guy that has done all of my prints for cheaper than what I spent on the egg crate and pvc. I like that I built everything myself though so I’ll take the loss there. I didn’t have the glue for the acrylic, so that was $22. Materials for just the build (not including tools/materials I got that I needed anyway) of the frag tank and AIO compartment were easily under $200.

Luckily a member offered to help with cutting the acrylic down to size, which would have otherwise been pretty difficult for me to do myself. I also picked up an AI 16 Prime for $100, an SPS frag, and promise of more frags once I got this up and running. The entire build including ATO, plumbing (I ended up using an old nano return pump I had), acrylic, and light was under $300.

I enjoyed the challenge of it, and am proud I built it with very minimal help. It’s also convenient to build a size for what you want. I will say that if I could go back I’d go with 8”-10” for height, just to have a little more to work with. Overall I’m quite happy with it though. You can see a video of the entire set up and a test GSP rock on my IG page @hunnas_stunnas
 
View attachment 82043
View attachment 82045
That was for the acrylic. Admittedly, I could have had a frag tray 3D printed from a guy that has done all of my prints for cheaper than what I spent on the egg crate and pvc. I like that I built everything myself though so I’ll take the loss there. I didn’t have the glue for the acrylic, so that was $22. Materials for just the build (not including tools/materials I got that I needed anyway) of the frag tank and AIO compartment were easily under $200.

Luckily a member offered to help with cutting the acrylic down to size, which would have otherwise been pretty difficult for me to do myself. I also picked up an AI 16 Prime for $100, an SPS frag, and promise of more frags once I got this up and running. The entire build including ATO, plumbing (I ended up using an old nano return pump I had), acrylic, and light was under $300.

I enjoyed the challenge of it, and am proud I built it with very minimal help. It’s also convenient to build a size for what you want. I will say that if I could go back I’d go with 8”-10” for height, just to have a little more to work with. Overall I’m quite happy with it though. You can see a video of the entire set up and a test GSP rock on my IG page @hunnas_stunnas
That's not bad at all! I can tell you did a phenomenal job with the assembly. I think I'll start stocking up for a build of my own soon.
 
I like that you made the AIO compartments large enough for an adult hand to fit in the compartments.
 
Why 1/2"? From my experience it's much harder to work with and with the height of your tank I'm confident you'd be fine with quarter inch. Just trying to see if there's something I'm missing here
 
Back
Top