30g Cube Modern Style Stand (Build Thread)

rededge2k1

Member
Supporting
Messages
499
Reaction score
20
Location
Roswell, GA
I recently completed a custom stand for nimrod (Rodney) and wanted to share the progress pictures with you guys. Rodney wanted a modern-style stand, painted gloss white, for his 30 gallon cube. Zero trim and clean lines were a must.

Below are renderings from my SketchUp design, tweaked by Rodney to his liking before the physical build began.

Back Panel

a.jpg
alt="" />

Shelf & Bottom Panel

b.jpg
alt="" />

Structural Sides

c.jpg
alt="" />

Top & Bottom Braces

d.jpg
alt="" />

Top

e.jpg
alt="" />

Side Accents

f.jpg
alt="" />

Door

g.jpg
alt="" />

Since Rodney wanted the stand to be painted, I used 3/4" birch plywood for the stand construction. Where the plywood edges would show, I covered them with 1/32" birch iron-on edge banding....but more on that later. Here you can see a sheet of 4x8 plywood cut into all the pieces needed to build this small stand:

Full sheet...

01-30gCubeModernStyleStand.jpg
alt="" />

All the crosscuts...

02-30gCubeModernStyleStand.jpg
alt="" />

And finally, all the pieces cut from the four crosscuts...

03-30gCubeModernStyleStand.jpg
alt="" />
 
Back panel layout...

04-30gCubeModernStyleStand.jpg
alt="" />

Cutouts and dados in the back panel...

05-30gCubeModernStyleStand.jpg
alt="" />

Cutouts and dados in the structural side panels...

06-30gCubeModernStyleStand.jpg
alt="" />

Countersinks for screws -- these will be covered by accent panels later and thus will not be seen

07-30gCubeModernStyleStand.jpg
alt="" />

Shelf (which divides the electrical compartment from the sump area) and bottom panel being glued & screwed to the back panel...

08-30gCubeModernStyleStand.jpg
alt="" />

09-30gCubeModernStyleStand.jpg
alt="" />

Pocketscrew holes in the bottom of the bottom panel, which will not be seen either...

10-30gCubeModernStyleStand.jpg
alt="" />

Structural side panels, more glue & screws...

11-30gCubeModernStyleStand.jpg
alt="" />

12-30gCubeModernStyleStand.jpg
alt="" />

These narrow plywood braces are used as supports in the front top & bottom of the stand...

13-30gCubeModernStyleStand.jpg
alt="" />

Bottom brace...

15-30gCubeModernStyleStand.jpg
alt="" />

Top brace...

16-30gCubeModernStyleStand.jpg
alt="" />

17-30gCubeModernStyleStand.jpg
alt="" />
 
The top is made of 3/4" plywood just like the case is, but since the edges will be visible, I covered them with iron-on birch edgebanding. This process is simple and only requires an iron and J-roller...

18-30gCubeModernStyleStand.jpg
alt="" />

19-30gCubeModernStyleStand.jpg
alt="" />

Plywood panel with completed edge banding...

20-30gCubeModernStyleStand.jpg
alt="" />

Top installed...

21-30gCubeModernStyleStand.jpg
alt="" />

Attaching the side accent panels....

22-30gCubeModernStyleStand.jpg
alt="" />

The top ends of these accent panels were primed before being installed, since it would be difficult to get finish in this narrow gap...

23-30gCubeModernStyleStand.jpg
alt="" />

Side accent panels installed...

24-30gCubeModernStyleStand.jpg
alt="" />

25-30gCubeModernStyleStand.jpg
alt="" />

Lining up the door for hinge placement...

26-30gCubeModernStyleStand.jpg
alt="" />

Boring 35mm holes for concealed hinges...

27-30gCubeModernStyleStand.jpg
alt="" />

28-30gCubeModernStyleStand.jpg
alt="" />

29-30gCubeModernStyleStand.jpg
alt="" />

30-30gCubeModernStyleStand.jpg
alt="" />

Door installed...

31-30gCubeModernStyleStand.jpg
alt="" />

Stand complete, all that's missing is primer & paint!

32-30gCubeModernStyleStand.jpg
alt="" />

33-30gCubeModernStyleStand.jpg
alt="" />

34-30gCubeModernStyleStand.jpg
alt="" />
 
The painting process begins...I used a HVLP conversion spray gun and 15g air compressor for all priming & painting.

Primer...

35-30gCubeModernStyleStand.jpg
alt="" />

Paint...

36-30gCubeModernStyleStand.jpg
alt="" />

Re-installing the door hardware...

37-30gCubeModernStyleStand.jpg
alt="" />

38-30gCubeModernStyleStand.jpg
alt="" />

39-30gCubeModernStyleStand.jpg
alt="" />

40-30gCubeModernStyleStand.jpg
alt="" />

Door hinged and lined up...

41-30gCubeModernStyleStand.jpg
alt="" />

Done!

43-30gCubeModernStyleStand.jpg
alt="" />

42-30gCubeModernStyleStand.jpg
alt="" />

44-30gCubeModernStyleStand.jpg
alt="" />
 
Can't say enough good things about Dustin and his skills. He is the consummate professional, kept me updated and delivered an excellent product. Anybody shouldn't think twice working with him on a project.

Thanks again Dustin!

Here's some initial pics of the stand he delivered:

Nice fit in the corner:
IMG_4206.jpg
alt="" />

Fits my sump perfectly:
IMG_4205.jpg
alt="" />
 
nimrod;532813 wrote: Can't say enough good things about Dustin and his skills. He is the consummate professional, kept me updated and delivered an excellent product. Anybody shouldn't think twice working with him on a project.

Thanks for the kind words, I'm glad you like it! And don't forget to post a picture once you have the tank up top & stocked -- it's going to look killer surrounded with all the gloss white.

Dustin
 
Back
Top